F.A.Q.

Explore common planning questions about parking blocks, speed bumps, and cable protection. Product dimensions, installation requirements, and accessories vary by model; use the selected product information when preparing your order.
Parking layout and vehicle control

1. Do parking blocks and speed bumps serve the same purpose?
No. Parking blocks help define a vehicle’s stopping position within a parking space. Speed bumps are placed across a vehicle travel path to encourage slower movement. Choose the category based on the task you need it to perform.

2. What measurements should I take before ordering parking blocks?
Record the parking space dimensions and note nearby curbs, walls, walkways, and landscaping. Share the types of vehicles expected to use the spaces. Product length alone does not determine placement; the layout also needs to account for vehicle overhang and pedestrian movement.

3. Should I select the same wheel stop size for every parking space?
That depends on the layout and intended vehicles. A compact garage space and a larger commercial parking space may call for different configurations. Review each area rather than assuming one product size will suit the entire property.

4. Can I use a wheel stop as a barrier to block vehicle access?
A wheel stop is intended to help position a parked vehicle. It should not be treated as an impact barrier or a device for securing an entrance. Explain whether your goal is parking alignment or access restriction before selecting a product.

5. What site details matter when planning a speed bump installation?
Provide the travel-path width, surface type, vehicle types, and intended location. Also identify nearby entrances, drainage paths, and pedestrian routes. These details help frame the product discussion and should be considered by the person responsible for the site layout.

6. Does a taller speed bump automatically make it a better choice?
No. Height is one part of the overall profile. The appropriate choice also depends on the vehicles, clearance, and intended application. Compare the dimensions and intended use of the specific models instead of selecting on height alone.

Cable protection and installation

7. How do I determine the cable channel size I need?
Measure the outside diameter of each cable or hose and identify how many need to cross the area. Compare those measurements with the usable channel dimensions, not the overall ramp size. Leave the product selection open until the cable fit has been checked.

8. Does a five channel ramp always suit a job better than a two channel ramp?
Not necessarily. Channel count describes how cables can be organized, but channel dimensions and the model’s traffic rating also matter. A ramp with more channels may be unnecessary if a smaller configuration meets the actual requirements.

9. Can a pedestrian cable cover be used where forklifts cross?
Do not assume it can. Pedestrian covers and vehicle ramps have different intended uses and ratings. Provide the equipment type and relevant load information, then verify the selected model’s specifications before using it at a vehicle crossing.

10. What does a load rating stated per axle mean?
It describes the load associated with one axle rather than the vehicle’s total weight. A total vehicle weight cannot be compared directly with that figure without understanding its distribution. Ask for the rating and any operating conditions for the exact ramp being considered.

11. Is the same mounting hardware used for asphalt and concrete?
Hardware selection depends on the surface and the product. Identify the installation surface when ordering and follow the model’s installation instructions. Confirm the recommended fasteners instead of assuming a single anchor type works for every location.

12. Are anchors and end caps included with every speed bump?
Inclusions vary by model. Review the exact item and confirm whether mounting hardware and end caps are included or ordered separately. List the full installation width and required accessories in your quote request to help avoid an incomplete order.

Project coordination and ongoing use

13. Can a new section connect to equipment already on site?
Connection profiles and dimensions can differ between product families. Send the existing model reference, measurements, and clear photos of the connection points. Similar appearance does not establish compatibility, so confirm the match before ordering replacement sections.

14. What should I send when requesting products for multiple properties?
Separate the requirements by location, including product references, quantities, surface types, delivery ZIP codes, and target dates. Identify any differences between sites so each location can be reviewed without assuming identical conditions.

15. How can I explain my project if I do not have a technical drawing?
A simple sketch and a few clear photos are a useful start. Mark the area to be covered, add approximate dimensions, and show nearby access points. State the units used and distinguish estimates from confirmed measurements.

16. Can I combine parking blocks, speed bumps, and cable ramps in one quote request?
List each product category and its quantity in the same inquiry, with separate notes for dimensions and accessories. Our team can review the request and clarify availability and fulfillment details for the items involved.

17. What should be checked during routine product inspections?
Look for movement, visible damage, loose or missing fasteners, worn visibility markings, and debris around the product. For cable ramps, also check covers and connections. Follow the product’s care guidance and have any concerns assessed before continuing use.

18. What information helps identify a replacement part?
Provide the original product name, order reference if available, and photos of the full item and affected component. Include measurements where useful. Confirm compatibility and part availability before purchasing a replacement.

Have a site specific questions?